Time Timer Watch PLUS Support

Please carefully read these troubleshooting tips for all models of the Time Timer Watch PLUS. You can also download the visual instructions (PDF 1PDF 2) and view the Watch PLUS Instruction Video. Time Timer’s USA-based support team is always happy to help you as well: support@timetimer.com.

How do I set the time?

  1. Press "Mode" until you are in Clock Mode. Then press and hold the Set button for three seconds.
  2. Use the plus and minus buttons to adjust the current hour.
  3. Then press the Next (Mode) button and use the plus and minus buttons to set the current minute, seconds, clock format (12- or 24-hour) and am/pm meridian.
  4. Press the Set button once to confirm.

How do I set the alarm?

  1. Press "Mode" until you are in Alarm Mode.
  2. Then press and hold the Set button for three seconds. Use the plus and minus buttons to adjust the alarm hour.
  3. Next, press the Next (Mode) button and use the plus and minus buttons to set the alarm time.
  4. Press the Next button and plus button to choose the type of alert (vibrate, audible or both).
  5. Press the Set button once to confirm.

How do I set the Timer to repeat in Time Timer mode?

  1. To set the repeat for the Time Timer mode, you have to first be in that mode. Hold down the set button, then press the mode button to cycle through the different settings.
  2. The repeat icon is above the icon for the original mode/custom disk mode. If the timer is set to repeat, there is a small icon of an arrow going in a circle. If the repeat is not set, then all you can see is an icon of a small dash ("-").
  3. After pressing the mode button to toggle to the dash icon (the icon will be blinking), the repeat can be set by pressing the + or - buttons to toggle the repeat on or off.

What is Original Timer Mode? What is Custom Timer Mode?

  • In Original Timer Mode, the full red disk represents 60 minutes.
  • In Custom Timer Mode, the red disk represents any amount of time you need.

Use Original Mode when you need 10 to 60 Minutes. Use Custom Mode when you need much more or much less than 60 minutes (5 minutes, 5 hours, up to 99:59 hours).

How do I set the Timer in original mode?

  1. Press "Mode" until you are in Timer mode (a portion of the red disk will display).
  2. Press the Set button for three seconds until the time begins to flash. Then use the plus and minus buttons to set the time and press Next to confirm.
  3. Then use the plus and minus icons to choose the type of alert that will occur when time runs out (vibrate, audible or both). Press Next to confirm.
  4. Finally, use the plus and minus buttons to select Original Timer and indicate the number of repeats. Press Next to confirm a final time.
  5. To start the Timer, push the red start/stop button.

How do I set the Timer in custom mode?

  1. Set your Timer using the instructions above.
  2. Then, use the plus and minus buttons to select Custom Timer and indicate the number of repeats. Press Next to confirm.
  3. Start the Timer by pushing the red start/stop button.

How do I replace the battery?

Battery life is estimated at 8 months. Replace your battery at the first sign of low power (no light or dim display). Take it to a jeweler or watch specialist and have the Type CR2032 battery replaced.

How do I reset the watch?

Replacing the battery (see above) will automatically reset the watch.

How do I replace or repair the watch band?

Please fill out the request a replacement form by clicking on the red button on the left.

Is the watch water proof?

The Time Timer Watch PLUS is water resistant, which means that it can be worn for general use in situations like the shower, a rain storm, or the pool.  While the watch can be worn in those types of situations, the buttons to set the watch should not be pressed while the watch is under water.  This can cause water to enter the main housing of the watch.  General wear and use should not cause water to enter the watch.  The watch is not suitable for diving.

 

 

 

What about my older Time Timer watch?

Although Time Timer watches manufactured between 2008-2011 have been discontinued, you can fix most issues quickly and easily. Our USA-based support team is always happy to help you, as well. Just email us at support@timetimer.com.

How do I set the time?
Please watch this video for instructions.

How do I set the Timer?
Press and hold S1 for three seconds to enter the settings mode. Press S2 to change the field to set. Press S3 to change the value of the field being set. Press S4 to exit settings mode.

How do I change the battery?
When the display grows dim or goes out entirely, it is time for a new battery. Using a small Phillip's head jeweler’s screwdriver, remove the four screws holding the back of the Timer onto the case. Gently slide the old battery from its slow, and replace it with a new CR2025 Lithium battery. Make sure that the positive ("+") terminal side is facing up.